Asus k7v t manual

Registered DIMMs are not supported see 3. Premature wearing of the processor may result when overclocking. Without sufficient circulation, the processor could overheat and damage both the processor and the motherboard. You may install an auxiliary chassis fan, if necessary. Install the Universal Retention Mechanism onto the motherboard. Insert the processor. Make sure that the processor substrate key is aligned with the Slot A connector key.

You may wear gloves to protect your hands from the sharp edges when removing processors. Page Smart Thermal Solutions 3. Conflicts will arise between the two PCI groups that will make the system unstable or cards inoperable.

Page 34 3. Page 36 See Onboard Serial Port 1 in 4. Page 37 Line In light blue allows tape players or other audio sources to be re- corded by your computer or played through the Line Out lime.

Mic pink allows microphones to be connected for inputting voice. Page 38 Pin 5 is removed to prevent inserting in the wrong orienta- tion when using ribbon cables with pin 5 plugged. The connector powers up the system when a wakeup packet or signal is received through the LAN card. SMBus is a specific implementation of an I bus, which is a multi-device bus; The plug from the power sup- ply will only insert in one orientation because of the different hole sizes. Find the proper orientation and push down firmly making sure that the pins are aligned.

Page 44 This optional connector is the digital link between the motherboard and your devices, such as CD player, sampler, or DAT recorder. Page 45 3. Page 46 This may require one or two presses depending on the position of the switch. Page 48 Shut Down, and then click Shut down the computer? The power supply should turn off after Windows shuts down. Page Bios Setup 4. Care- less updating can result in your motherboard having more problems! If this happens, your system will need servicing.

Page 52 4. This window displays the help text for the currently highlighted field. NOTE: The item heading in square brackets represents the default setting for that field. Page Main Menu This is required to support older Japanese floppy drives. Floppy 3 Mode support will allow reading and writing of 1. Page 59 IDE devices. Note that selecting a frequency higher than what the CPU manufacturer recom- mends may cause the system to hang or crash. See System Hangup later in this section.

Page 64 OFF your system and restart. You will then be led to BIOS setup to adjust the configurations. The EEPROM on the memory module stores critical parameter information about the module, such as memory type, size, speed, voltage interface, and module banks.

Page 66 It can greatly improve the dis- play speed by caching the display data. You must set this to UC uncacheable if your display card cannot support this feature; otherwise your system may not boot.

Shadowing a ROM reduces the memory available between K and K by the amount used for this purpose. Page Power Menu Windows 3. For Windows 98 and later, APM is automatically installed. Page 75 4 seconds will place the system in sleep mode. Regardless of the setting, holding the ATX switch for more than 4 seconds will power off the system. Page 77 [By Date]. Page Exit Menu This option should only be used if you do not want to save the changes you have made to the Setup program. If you have made changes to fields other than system date, system time, and password, the system will ask for con- firmation before exiting.

You can then return to other menus and make changes. After selecting this op- tion, all selections are saved and a confirmation is requested. Select [Yes] to save any changes to the non-volatile RAM. Page Software Setup When prompted to restart, select No and then follow the normal setup procedures later in this section. NOTE: The screen displays in this and the following section may not reflect exactly the screen contents displayed on your screen.

Page Registry Patch For Via Chipset You may not, however, be able to use immediately the devices associated with the drivers or software because these drivers need to be enabled. Page Via Pci Irq Routing Miniport Driver You may not, however, be able to use immediately the devices associated with the drivers or software because these drivers need to be enabled. Page Audio Driver Only With Onboard Audio Option You may not, however, be able to use immediately the devices associated with the drivers or software because these drivers need to be enabled.

Once the Emergency Clean disk is created, click OK. NOTE: The item heading in square brackets represents the default setting for that field. Page Main Menu This is required to support older Japanese floppy drives. Floppy 3 Mode support will allow reading and writing of 1.

Page 59 IDE devices. Note that selecting a frequency higher than what the CPU manufacturer recom- mends may cause the system to hang or crash. See System Hangup later in this section. Page 64 OFF your system and restart. You will then be led to BIOS setup to adjust the configurations. The EEPROM on the memory module stores critical parameter information about the module, such as memory type, size, speed, voltage interface, and module banks.

Page 66 It can greatly improve the dis- play speed by caching the display data. You must set this to UC uncacheable if your display card cannot support this feature; otherwise your system may not boot. Shadowing a ROM reduces the memory available between K and K by the amount used for this purpose.

Page Power Menu Windows 3. For Windows 98 and later, APM is automatically installed. Page 75 4 seconds will place the system in sleep mode. Regardless of the setting, holding the ATX switch for more than 4 seconds will power off the system. Page 77 [By Date]. Page Exit Menu This option should only be used if you do not want to save the changes you have made to the Setup program. If you have made changes to fields other than system date, system time, and password, the system will ask for con- firmation before exiting.

You can then return to other menus and make changes. After selecting this op- tion, all selections are saved and a confirmation is requested. Select [Yes] to save any changes to the non-volatile RAM. Page Software Setup When prompted to restart, select No and then follow the normal setup procedures later in this section. NOTE: The screen displays in this and the following section may not reflect exactly the screen contents displayed on your screen.

Page Registry Patch For Via Chipset You may not, however, be able to use immediately the devices associated with the drivers or software because these drivers need to be enabled. Page Via Pci Irq Routing Miniport Driver You may not, however, be able to use immediately the devices associated with the drivers or software because these drivers need to be enabled.

Page Audio Driver Only With Onboard Audio Option You may not, however, be able to use immediately the devices associated with the drivers or software because these drivers need to be enabled. Once the Emergency Clean disk is created, click OK. Page Acrobat Reader Vx. To uninstall any program, see 5. You may use this function if a program does not provide its own uninstallation program. Clicking the icon will allow you to see the status of your PC.

Page Using Asus Pc Probe 6. Temperature Warning threshold adjustment Move the slider up to increase the Page 97 CPU temperature and predefined thresh- old. Click to open the previous set of Monitoring options. To run a program, click Execute Program. NOTE: This feature is currently unavailable. Page Yamaha Xgstudio 6.

Page Troubleshooting For the name of the select switch, refer to the owner's manual for your external tone generator. Page Modem Riser 4. Secure the MR card onto the chassis with the screw removed in step 2. Replace the computer chassis. Click Diagnostic and then click the designated COM port as shown. Click More Info.. If the computer sys- tem successfully communicates with the modem, responses will be displayed as shown. Bit Binary Digit Represents the smallest unit of data used by the computer.

A bit can have one of two values: 0 or 1. Page IDE devices integrate the drive control circuitry directly on the drive itself, elimi- nating the need for a separate adapter card in the case for SCSI devices. Page Developed by Rambus, Inc. Page USB 2. Wake-On-LAN Computer will automatically wake-up upon receiving a wake-up packet through a Network interface when it is under power soft-off, suspend or sleep mode. Print page 1 Print document pages.

Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR.